As a stationary pond is beautiful and useful in terms of recovery, it is also complex in care. Water needs to be cleaned, cleaned, rescued through the incoming debris without stopping. However, if the building is covered with a transparent pavilion floating above the water, then the upbringing becomes easier. Even those owners who mounted the cup open, over time, build pavilions over it for the pools themselves.
What is the purpose of the whole pavilion?
Completing the pavilion to the pool, the owner will receive the following"bonuses":
Water is less dying from the surface.
Much less heat loss, and probably costs for heating water. In addition, it will lengthen the terms of the swimming season.
Dirty precipitation and a dusty, dusty leaf will not fall into the pond, and the owner will save for chemical filtration and cleaning of water (if the pavilion of a closed type).
Ultraviolet rays will collide with a barrier and fall into the pond already refracted. And probably, their destructive counteraction for the wall and the bottom is rather weaker, which will lead to an increase in the term of building the pool materials.
In winter frosts, the temperature near the pavilion is higher than for the street, it is likely that the designs will not have to break through the tests with extremely low temperatures, why some materials and the order of water supply may become unusable.
Rules for choosing a pavilion design
In order to build a pavilion for the sake of the pool with your own hands, you need to be conditioned with its design.
Low pavilions
If the reservoir is used at times, and the rest is time idle, then the cheapest option is a rather short pavilion with a height of less than a meter. It will fulfill the most important function - protection of water through the sun, precipitation and debris. And if the owners do not plan to dive from the sides, then it's enough to execute the sliding section and through it to get into the water. Low pavilions are comfortable, if the pool is used exclusively in the summer season
There are also structures with a height of about 2 meters. In their for the sake of convenience, a door is mounted in the end. This variation of the pavilion is made according to the principle of an ordinary greenhouse with the introduction of a metal profile and sheets of polycarbonate. It is permissible, of course, instead of polycarbonate to stretch the polyethylene film, but neat visibility through it will suffer, well, the wear resistance of the film coating is weak.
The highest pavilions
The highest pavilions have a height of 3 meters and are used not only to protect the pool, but also serve as a lovely recreation area for the sake of the owners. The greenhouse climate allows you to arrange flower arrangements in accordance with the perimeter of the bowl, evaluate sunbeds or rocking chairs for recreation. However, in this case, if the boundaries of the pavilion are much larger than the size of the bowl. The highest pavilions replace classical gazebos for owners, as there are enough areas for their rest and quite warm even in winter
A more economical option is the pavilion, who is built around the perimeter of the bowl, speaking for a dozen see. It can exist all closed or half-closed. The semi-closed variation protects the bowl or tokmo from one side (more often from the side where the wind blows), or from the ends, leaving the middle open, or from the sides, leaving the ends open. Such a pavilion will not provide the highest protection, but the barrier for the sake of wind and garbage will create, and the hosts will receive a shadow zone, which is allowed to hide through the scorching sun. The semi-enclosed pavilion protects the pool share, and it is better to mount it from the side of the wind or through greenery
Sliding constructions
In any suitably height, the pavilion increases the comfort height of the order of the sliding sections. Their base is a rail system (like in the commander's closets), according to which the sections can hang out and enter one of the other. Moving them to a single end, the hosts receive a tent for the sake of creating a shadow, and in case of precipitation they can vividly insulate the bowl. Sliding or telescopic pavilions move in accordance with the rail system and can all leave the water area of the basin
The choice of the form of the pavilion depends on the basin of the pool. For the sake of round bowls, dome-shaped models are used, for the sake of rectangular ones - in the form of a letter"P"or a hemisphere. The most complex are pools of incorrect forms. For the sake of their do asymmetric"sheds." For the sake of the round bowls, the more successful form of the pavilion is the dome
Development of the creation of the pavilion with your own hands
From an economic point of view, the product of the pavilions is justified on its own, but if you have experience, the installation of the highest building can be delayed for a couple of weeks. Byl, some dacha owners simply have no choice, the causality for the sake of a bowl of unusual shape to find a proper"roof"is not always possible. And probably you need to buy materials yourself and arrange a pavilion. Let's see, it's kind of fulfilling for an example of a semi-closed polycarbonate structure.
Determine with materials and form
Pavilion of polycarbonate is assembled according to the principle of an ordinary greenhouse
For the sake of coverage we will extract polycarbonate, which is usually covered with greenhouses. A skeleton will create a profile pipe.
In order to minimize costs and simplify the installation, we will create a structure open from the ends, put it for the base of the pool or its finish and leave it to be able to decompose for the winter.
For the sake of swimming, a huge elevation is not needed, hence a rather two-meter pavilion.
Fill the base
Being of all seeming lightness, polycarbonate and metal-profile have great authority, hence the base for the pavilion should be reliable. If there is already a recreation place near the pool and tiles laid out, then the mounting is allowed steadily for it. Through the design of the pavilion, the base is forced to walk again for 7 cm, the future, in order to firmly hold the full luggage
The rest of the owners will have to fill the base with a width of half a meter, the width of which should go through the base of the frame for approximately 7 cm to the sides. Concrete should be reinforced by laying out squared cells with a side of 20 cm. The basis for the sake of the pavilion is forced to exist thick and strong, as the authority of the whole design can achieve a ton and more
Create a skeleton
For the main arcs of the frame, a wide pipe is needed, for which it is permissible to fasten the two edges of the polycarbonate sheets adjacent. Its length is 1 height (2 m) + width of the pool.
Pipes need to arch arches. It is better to entrust this to the specialists, and anyone who can eat welding is allowed to perform by themselves. The proportion of the pipe that should be bent, cut from 3 sides with a circular saw, carefully bend, fixing the edges in the vice, and then without cutting the cuts. Welding places are ground.
We fix the base of the frame using the bolts to the foundation. The base of the frame is attached to the foundation or trim pool using bolts
We put the arc, also fixing the bolts and nuts (If the variation is quite indiscriminate - it is allowed to brew). The gap between the arcs is a meter. We are fixed to the base with a bolt without the need for an arc
Between the arcs fix the stiffeners, alternating then 2 edges, then 3 for the lumen. Arc take for double bolts for the sake of reliability
The finished skeleton is treated with anti-corrosion agents and painted in an extraordinary paint.
Cover polycarbonate
We designate for polycarbonate sheets (the paint and thickness of which you choose yourself) the places where they will tolerate the pipes, and drill holes. They must exist a little more than the thickness of the screws, because for the heat polycarbonate"plays", and is forced to exist for expansion.
We trim the finished carcass with polycarbonate sheets. The sheets are fastened with screws, and near the bonnet one must certainly put iron (zinc-coated!) Washers in order to close the holes. Carbonate sheets must lie down for the profile pipe butt-end
From the inside of a permanent place of fasteners and joints are smeared with sealant. All the joints and fastenings are lubricated with sealant
The concrete base must be insulated from both sides through water and precipitation by means of decorative finishing with ceramic granite, tiles, etc.
It should be noted that the more often you decompose the structure, the faster it wears. For no reason, think about whether it is important to strip the pavilion before every winter. This is justified, if only in the winter interval the dose is quite empty, and nobody will clear the sediment from the pavilion in case of heavy snowfalls.
Home pavilion from the greenhouse? Free!
Комментариев нет:
Отправить комментарий