Of the assortment of construction materials suitable for the production and installation of gates, personal builders in most cases choose profiled. The importance of this building material is given according to a number of circumstances, between which it is allowed to note strength, longevity, decorativeness and, of course, affordable value. The profilist is made in industrial conditions from iron sheet by the method of cool kata. On both sides for sheet metal profiles is applied a layer of galvanizing protection, protecting the metal through corrosion and early destruction. For the sake of additional protection and increase in the decorative properties of the corrugated sheet is covered with a polymer layer, the coloring of which can be very different. In order to make the gate from the profiled sheet with your own hands, you just need to find a couple of days off and a couple of free hands. After all, two are always more fun and quicker. Byl, except for the hands it is necessary to stock up the welding machine and the smallest set of tools. What are the designs and how good is the corrugated board?
Why specifically profiled? Since it provides:
Longevity of the design. The self-made gates will last for a quarter of a century, without any special care and repair.
The short authority of the building materials used, which simplifies the installation, and also the delivery of only the required object.
The ability to choose the texture and color, based on the preferences of the owner of the house. The gate, combined with a fence, Thrift for paint, because the gates from the profiled sheet do not burn out by the action of the sun's rays and do not fade with the influence of precipitation. To be buying, pay homage to the manufacturer, because fakes may not have such properties.
Except for all other things - of course this is a low value compared to other building materials and taking into account their features.
therefore, there is a certain number of types of constructions of gateway, among which the most widely used two options. hinged and sliding sliding gates from metal sheets to construct their own hands is quite difficult therefore for the implementation of the tasks better invitations from Sit Prof. builders Without the help of others, it is easier to assemble a swing gates, consisting of two similar halves, each of which opens to its side. Naturally, it is permissible to perform one huge flap, turning to one side. All to be this option falls a big load for the loop, for which all this"mahin"is hung. Consequently, most of the developers prefer the traditional two-leaf design of the swing gates. For the sake of the passage for the area of the car and a small truck is enough to build a gate width of 4 meters. The height of the welded frame can exist 2-2.5 meters.
Proud! To be free space wicket is allowed to be installed close to the gate. Preparing holes and installing gate pillars Bearing poles for the sake of the gate are allowed to be constructed from the following building materials:
a cross-section of which is 150 for 150 mm;
a round solid log with a diameter of more than 20 cm,
a channel beam having a thickness of 14-16 mm
shaped tube (80x100 mm), wall thickness of which is 7 mm.
Then markup portion start to dig holes for the installation of portal columns, using for this everyday shovel or gardens drill Determined with the material for the sake of the pillars, proceed to the pit of pits, the abyss of which is equal to one third through the elevation of the elevated part of the gate pillars. With all this, it is necessary to take into account the fact that the gate leaf gate is usually made for half a meter shorter than the pillars. This stock allows you to ensure the height of the lower edge of the gate through the surface of the soil for 20-30 cm, also throw again a pair of 10-cm cm above for the sake of welding decorative parts that adorn the entire structure.
The stability of the gate is dependent on the strength of the poles, therefore, for the sake of their production, metal rolling is chosen. For the installation of a profile pipe or a channel beam, a hole is drilled for 1.2 meters in depth and in a cross-section of about 20-50 cm. The prepared iron pillars are lowered into the pit, set according to the level in a strictly vertical position and filled with cement. The preparation of poles consists in cleaning their surface through rust, the next priming and painting, and also in the installation of upper plugs preventing the ingress of snow and rainwater. The installation of poles for the sake of securing the door leafs is done in a strictly vertical position with the following fixing them with a cement solution
Composing in a theme: postroiki/ustanovka-stolbov-dlya-zabora Installation of poles for the sake of a fence: methods of installation of different designs
Selecting a profile sheet for the sake of skinning the frame of the gates Profile sheets are divided into three groups that differ well from each other in width, rib height, degree of strength. Every society has its own marking:
"C" - a corrugated corrugated board made of zinc-coated sheet of small thickness with a small rib height. Lightweight and at the same time strong material,"NA" - corrugated board, distinguished through the material of the previous brand with a higher wave height and wider width. This affects their weight and strength level.
"H" -"bearing"profiled sheeting, used to build steel hangars and the installation of roofs of significant area. Thick profile sheets of this brand have an overestimated level of strength. To use them for the sake of shelling the frame of the gate is expensive and inexpedient. The best way is to make the gates from the profiled sheet C8 and C10 (numbers indicate the height of the wave in millimeters). The thickness of the profile sheet varies between 0.4 and 0.8 mm. The leaflets of this material weigh in at 25 in front of 40 kg, therefore to cope with their erection at a force of two workers. Lifting conditions will not be enticed, which will save for the cost of the gate.
Гордо! Резку профильного листа сообразно необходимым размерам лучше запрещать для заводе (быть наличии таковой способности). Для особом оборудовании, имеющемся для производстве, удается обеспечить верность резки, верность полосы реза, также минимизировать число вероятных повреждений.Действие рамного каркаса
The frame for the production of gate leaves is allowed to be made of wood beams or from a profiled tube of rectangular cross-section (40x20 mm), whose walls have a thickness equal to 2 mm. If the poles are supplied with iron, then the frame needs to act from a similar material. There is a rim of the gate for a level platform, which can accommodate at least one leaf. That corners have left direct, use the precise measuring devices (angles). It is allowed to use and self-made device from the rope, which is formed in a right-angled triangle with sides 3,4 and 5 dm. The rim is welded from the profile in the form of a rectangle with the help of a welding inverter, while the corners are precisely reinforced with iron corners, which give the construction a great hardness. The long sides of the frame are divided into three parts and welded to the marked places by parallel bridges, sealing the joints also with iron corners. In these places, the gate hinges are welded. The production plan of the frame for the sake of the gate from a profiled pipe having a rectangular or square cross-section. The method of fixing the closed door leafs Proud! If you intend to execute a gate in the gate, the frame is not enough if. In one of the wings, with a longitudinal and transverse webbing welded to a rectangular frame, a frame of 80 cm for 180 cm is made. At the same time, the loops are moved to the bottom and top edges of the gate. Galun gate frame with sheets of profiled sheet To the frame skin with a profile sheet proceed at the same place for the frame assembly. For the fixation of the corrugated board, special fixing elements are used - self-tapping screws with a hexagon head, painted in the same paint, which is the main material. To the gate hinges, sheets with a wavy surface are bolted or welded. The length of the hinges for the sake of the gate should exist more than 1 meter, and their thickness - more than 3 mm. To assemble the assembled flaps, it is permissible to remove a small winch, which is attached to a support placed over the gate pillars. For the ground lay the bar, for which the gate leaf is installed, in order to fix the ends of the loops with the welding for the column. It is permissible to secure the hinges with bolts for the sake of safety. The bars are removed from the gates of the gate and are inspected as freely they are locked and opened.
Комментариев нет:
Отправить комментарий