Stationary brazier made of brick by our own hands...

Stationary brazier made of brick by our own hands: we equip a picnic areaThere are warm days and summer residents are rushing to bait the sites. There comes a time of hassle. However, in the general bustle, it is proud to feel the beauty of the awakening nature, to breathe in a full, unblemished atmosphere, devoid of urban smog and burning. The matter is work, however, we devote it to the whole week for no reason, and trips for the dacha should, at first, give pleasure. Every departure for nature is accompanied by classic shish kebabs. For no reason why the desire not to build a brazier of bricks for the plot with their own hands? It is always permissible to extract it sufficiently in accordance with its purpose. After all, the one that can perfectly rest, and do enough with the soul!
Splitting a place for a picnic
If we just have an opinion, like doing a brazier of bricks, we should immediately tie this building to the ground at the level of thoughts. Both the dimensions and the outward appearance of the building can be submitted through places where it is quite enough.
The general requirements for the site are ordinary:
the area must be flat;
consider the wind rose so that the bustle of cooking does not interfere with neighbors, does not get into the recreation area or to the house and does not strangle the cook;
the similarity of the site to the house is needed, for example it is easier to provide it with water and light, Also, you do not have to move dishes and food away.
It is worthwhile to plan the entire area for picnics. The picnic zone for the dacha should not exist overloaded with structures. Quite of a brick barbecue, stands about products, comfortable benches and portable table
The base provides the strength of the construction as a whole, so be it construction no need to rush: advance than through two weeks after pouring the date he was drunk not quite
Must definitely reinforce the base. For this purpose it is permissible to remove reinforcing rods or reinforcing mesh. If we select a grid, then it will have to be laid twice. First we fill the solution for the third part through the base elevation, then we place the grid discharge, then we fill the base for the third part and we lining the one more bit of the grid, then fill the base before its full size.
If the base will accommodate the rods, then put them then pour half the base. Moderately, three bars are laid out according to 100-105 cm in length, and later the full remaining volume is poured. So that after the rainwater flows freely from the walls of the barbecue, it is allowed to perform the site with a small (1 cm) slope. In order to gain strength, it is left for two weeks alone.
Main construction of masonry
If we want to arrange a brazier simple, but vividly and accurately, we need to perform a kind of"fitting". For the sake of this, for the work finished for the forthcoming work, we lay the building of bricks dry. Such a preparatory estimate allows in the forthcoming to extract only halves and whole blocks. If the grate and pallet were prepared by us in advance, we must take into account in the future construction of their clear dimensions. The line of the future masonry is outlined, fixed and enough to serve us for the sake of being guided. The main building of bricks should be laid out for the sake of fitting dry, but taking into account the fact that there is enough mortar to be bricks
The brick is hygroscopic: it absorbs water freely. If it is not prepared in advance for future work, it can absorb all the water from the masonry mortar. The building will not be strong. That this does not happen, because of the day before the work, the brick should be perfectly dipped. It is either poured in water in containers, or well poured with garden hoses. Before the work, the bricks must exist wet from the inside and dry out.
We prepare the masonry mortar at the rate of 1 part of cement, 3 parts of sand and a quarter of slaked lime. According to the mixture, the masonry solution is forced to suggest thick sour cream. It remains to check once again for all-out measurements and decompose the prepared brick for the masonry solution strictly in the order in advance. Between the bricks the place must exist perfectly filled with substance. In order to safely sink the blocks in the solution, they should be tapped from the top with a trowel handle or with a hammer.
Raise the mangal base
The main structure of the building serves as a reference point for the sake of all the following, which will be cured in a checkerboard order: the individual future content goes out-shifted relative to the previous one by one second brick. It is necessary to build the build up from the corner, and later fill the side walls. Masonry mortar should be appointed between rows and do not forget about the side surfaces of the bricks, excessively carefully remove
The plane of the structure should be tested accurately, using for this purpose the construction height and the plumb line. Act this should not be less than three rows, if the building can end up skewed. The masonry must be reinforced for corner joints with iron wire. If additional fixing of the brazier is not planned, it is allowed to remove the hose of the garden hose in order to give the welds a cautious appearance.
Stops for the grill and brazier > For the sake of the base, place iron corners or reinforcement bars. For them, and laid out the base of the furnace from the bricks. At us this employment is played by the iron pallet. The main contract, so that the firebox is freely cleared through the ash.
In the furnace area, the side gaps, unfilled by the substance, should be thrown in the masonry made of bricks. This will ensure the entry of air into the chamber. After all, without the influx of oxygen, the effect of burning fuel is not feasible. The building of the frypot and the installation of the pallet, grates and countertops - this is the finishing stitches. Through their properties depends on the external appearance of the structure and your action through the work done
The grate can be installed for iron rods, which are pre-mounted in the brick wall, or for the protrusions of the brickwork itself. Such protrusions are formed if the bricks are laid not across, but across the wall. It is necessary that they act in the interior of the brazier for the same height.
The structure of the working surface
The worktop must match the type of the resulting stove and be comfortable for use. It is allowed to take a strong floor or paving slab. For the sake of the working surface it is proud that it was strong and perfectly washed. The matter is actually fulfilled, but experts recommend that you allow your brazier to dry out for a few weeks before starting its operation
If the location of the brazier was planned to be a trouble for the water supply and drain, it is better to plan them in advance, as it is easier to make pipes through the base. For no reason they will be least noticeable, and the type of construction is rather aesthetic. The explanation of the site is not superfluous. For the fresh summer air, rest in the campaign with the production of shish kebabs better in the evening time, if not hot. Now you understand, it's kind of lively and free to build a brazier out of bricks.
You will be introduced to the only version of the brick brazier: