Garden sawmill from circular saws: Garden area...

Garden sawmill from circular saws:Garden area - a room where you can enjoy luscious greens for breakfast and bird trills in the morning, also cheat like time with utility, immersed in the freshest colors of nature. If you test the park from a more prosaic point of view, then the product of a careful site is unrealistic without eliminating plant waste. Spring pruning of fruit trees , slicing old strawberries and raspberries, a lot of weeds then weeding out the beds - all this is stacked up in order to burn out according to the end of the season. Economical owners who understand, like, are allowed to extract these wastes for the sake of usefulness, make compost heaps for the plots, which from 3-4 seasons only convert this matter into a good organic fertilizer. Deciding to make a garden chopper with your own hands,
The mechanism of the grinding device
Home garden shredder will help not only to take practical advantage of the waste, but to facilitate the guidance of beauties for the site. With the help of such a chopper, it is permissible to crush any plant parts into a small chip. Such chips look curiously as a decorative mulch for the sake of paths and flowerbeds
The chopper works according to the principle of a meat grinder, in which a branch of 1,5-7 cm, getting into the receiving hopper and moving to the grinding system, is freely grinded into a small chip. The hopper is a design that prevents the clothing and hands from getting into the edge of the rotating knives. The order of grinding consists of a mill and several knives. The thickness of the shaft depends on the purpose of the device, for reasons of grinding the thin 3 cm branches, an 8 cm elevation is established. The grinder should be worn with goggles and gloves
The productivity of the technology is directly in depending on the power of the motor. For no reason the grinder, whose motor power is in the spectrum before 2.6 kW, is able to grind the branches d=5 cm.
Stages of assembly of the construction
Selection of the necessary materials
The home garden shredder is not much different than the industrial analogues of these devices. Stationary shredder is allowed to perform for the base of a circular saw. For this in the unit, it is sufficient to change disks for cutting a hill or a milling cutter, and also to attach a receiving bunker. Or extract these saws as a shredding device, placing a lot of them for the shaft at once.
Creating a garden chopper with your own hands"from scratch"must first purchase a motor. The electric motor is a good option for the sake of quick grinding of raw materials in relatively small volumes. The electric motor is silent in operation and does not emit exhaust fumes at all. Such properties of the electric motor make it possible to extract it not only for the local area, but also in enclosed premises. An unprecedented flaw in the device is the need to connect to the power supply system. For the sake of working with coarse material in rather large volumes, it is more preferable to extract a motor block whose power is much higher than the power of a conventional electric motor
Suggestion. The introduction of circular saw blades with carbide nozzles will make a safe and long knife, who does not ask for a repeated procedure of undercutting. For the sake of assembling a high-quality knife, an average of 10 before 20 saws is 6-10 cm wide.
Installing cutting blades
Cutting saws are dialed for the stud - the axis, the diameter of which is equal to the width of the landing discs. For the assembly of the cutting device, nuts and washers of the same size are also required. In advance, you need to prepare thin washers, which can be cut out of plastic. These washers will be required for the sake of breeding discs for an equidistant gap well-wisher through a friend so that the rotation of their slightly protruding teeth does not cling to each other. The number of washers should exist for 1 element less than the number of disks. For the disc threaded pin, a pulley is installed, who can be taken through pumps or through a VAZ generator. For the rotation of the axis, two bearings with internal d=20mm are required
Action and ennobling of the frame
The frame can be welded from profiled iron pipes for the sake of fixing the rod of the motor block. To the welded structure, the disk is fastened in such a way that it can alternately alternate with the circular saws. This position will allow, if necessary, adjust the tension of the drive belt. For the sake of supporting the branches during processing, it is permissible to attach a stubborn bar from the profile to the structure
Mounting the casing and bunker
h3>The housing for the construction can be cut from zinc-coated steel, but it is more preferable to make it from sheet metal. The material of the receiving hopper production can be run by ordinary zinc coated steel. The casing is put directly on the cutting block.Advantages of a homemade machine
A garden shredder with its own hands, as a reward through industrial execution models, is more universal. It can be extracted not only for the processing of branches and grass, but also for the crushing of fruits and various types of household garbage. A strong unit is able to overcome even branches with a diameter of 10 cm
The position of the motor at the same level with respect to the knives makes it possible to prevent its breakage through the ingress of moist stems. The case with the unit is simplified due to the fact that nowadays it is not necessary to care because of the moisture content of raw materials and to choose branches according to the size.
Home garden shredder has the highest productivity: circular saws with a tremendous speed are able to process even thick enough branches. The prime cost of the chopper will be twice cheaper, and the power - at times more. The aggregate made by this method is not more terrible than the expensive industrial garden tool.
It is possible to think up many variants of a design, all the way through fantasies, resourcefulness and desire of the craftsman.