Between the necessary things stored in the utility...

Between the necessary things stored in the utility room of the economic masters of suburban areas, it is always possible to find devices and devices for cutting woody species. It can be a jig saw, a hand saw, a comfortable electric saw, or a strong unit working for a watery fuel. Each of the"assistants"asks for certain abilities of work and attentive care. For example, the owners of a tool working for electricity should know what chains are for the sake of electric, it is difficult to change them without the help of others and the ratfil is suitable for correct grinding.
Logging in huge volumes or the rigors of working for the street requires buying a more massive tool - chainsaws. All if you sometimes have to correct the city, make a correction at home or cut a fair amount of logs, then an impeccable inventory is an electric saw. It is comfortable to use in limited places - inside the house, in the barn or in the utility room, also for the site, if there is a power key nearby.
What are the advantages of the power tool? He does not ask for time to prepare the fuel consistency and cuts more than the gasoline counterparts. Minus the only - sparing order of use. It will be necessary to get used to interval sawing of wood species. It's likely that after about 40 seconds of work for the saw, you need a"breather"in about 20 seconds.

Developing the right cleanup
It's naive to delve into, which always drank quite unnecessarily well, like on the day of purchase. The woody breed, even compliant and soft, is a fairly healthy matter, the impertinent gradual blunting of the cutting surfaces. After a certain interval, who is almost in everything depends on the activity of using the tool and the quality of the tree species, the mountain will become dull, and its sharpening will be necessary. If you do not sharpen the teeth by the way, they will lose shape, they will become worthless and you will need a full reward instead of correction, and this is economically unprofitable.
Do not miss the moment!
There are no defined intervals between repair works. Usually sharpening is required if signs of blunting begin to show up. The only one of the main features is the configuration of the size and appearance of the chips. Due to the severity of the cutting edge of the teeth, it becomes small and more black than usual, and sometimes reminiscent of a speck of dust. The experienced craftsmen can find the need for sharpening not according to the characteristics of the sawdust, but according to the work of the electric saw. In the process of sawing, an unusual vibration arises, which in the forthcoming can cause the death of an asterisk and the wear and tear of principal nodes
If there are suspicions, take a close look at the mountain itself. For sharp parts, there should be no chips, radii, damages, and the appearance of the cutting edge must be kept initial. If you saw the smallest irregularities in the configuration of the teeth - the mountain needs sharpening. In the blunt tooth, the cutting edge is sewn according to two fronts: in the frontal part of the scapula and in line with the side cut strip. During sharpening, the shape of the entire cutting part should be corrected
Which are the recommended masters?
The inhabitants of huge cities stand before the choice: to eat to be able to sharpen the mountain of an electric saw in the service center or to sharpen without the help of others, with the help of special tools. Owners of power tools from small towns and villages do not have such ability, therefore, it is better for them, despite the sum of the process, to correct the chains themselves. However, in self-sharpening, you can eat your own plus-thrift of money. The advantage of sharpening the 1st tooth with the corrector of the limiter will cost 100-120 rubles, an increasing number of service centers make orders to be small amounts after 5000 rubles and more (retribution is in progress according to the number of teeth of the whole chain)
The importance of proficiency is the highest quality of work. The mountain is removed from the tire, pulled for a special machine, set the angle of sharpening and alternately the individual canine teeth rule. The accuracy of sharpening is determined by tenths of a millimeter.
Is it permissible to imprison a mountain with a ratfil?
Some master craftsmen are specifically causeless and act - to be the first symptoms of blunted links take a ratfil and fix angle of the cutting edge. All the tools are not suitable, you should stock up on a special set, which includes at least four necessary devices:
small ratfil for correcting the depth limiter;
the rift curve with the reference lines; li>value; <
For the sake of sharpening the mountain is left for the tire, and the tire is fixed in a vice. Ratfil is forced to respond to the teeth according to the width. A tool for easy grinding of the electric saw chain is allowed in the building hypermarket, the average value of the 1st set is 300 before 900 rubles.
See, that he only on 1/5 a share acted over the sharpened part. The main canine is advised to mark, so that suddenly it does not enter for the 2nd circle. Movements must exist rhythmically and accurately, not separately, but only in one direction.
Then a few sharpening should be handled and the limiter, who eventually loses its shape. The value is applied to the edge, the end side to the stop. If the limiter noticeably comes out from the border of the caliber, it should be trimmed with a flat ratfil. The location of the tool is perpendicular to the tire. During sharpening, look out from the motion of the ratfil, who is forced to be near the angle of 90? in accordance with the bus. Try to understand the amplitude and number of movements so that the teeth of the chain are sharpened identically for the whole chain
The chain teeth wear out unevenly, therefore you will come across the fact that they have different heights. In this case, it is necessary to find a more stagnant element and be identified according to it True grinding for the machine
It's impossible to use the ratfil for the sake of fixing the cutting edge, because the lie and uneven grinding lead to a rapid deterioration of the chain. Even if you have power, and the sharpening effect seems to be quick and uncomplicated (and it takes 6 hours before 8 hours), try using the machine - a more effective device.

All machines for the sake of sharpening chains are divided for manual and electronic. Lightweight gun - a simple structure, outside resembles a frame or a jig saw. For the sake of manual work, the tire with the chain must be firmly fixed (no need to remove the saw) in the vice, and then alternately cultivate a separate canine. The compactness, short authority and comfort of transportation allow the tool to be freely laid off for long distances if need arises. Hand-held machines have an ordinary design and low dignity - 850 before 1700 rubles. The best manufacturers of manual grinding equipment are Oregon and Favorite
Be buying a second option - an electronic model - you will certainly need a power switch, which is probably what it is unrealistic to live sharpening far through the sockets. But the property of the work is quite enough for the routine above, besides, the power plants have a set of necessary functions:
dealing with different kinds of circuits;
adjusting the depth and pitch of the cut;
a clear formation of the limiter;
setting a suitable cutting angle.
Before the work should painstakingly learn the annotation and perform a trial grinding for 1 tooth. Then set the characteristics according to the first tooth, so that all the following elements are consistent with it. This guarantees a similar sharpening of all the teeth, as it should, good performance and the highest performance.
Like to prolong the existence of the chain?
And the end is pretty tips for those who prefer to do more and work less repairing, replacing and sharpening chains. Remember that the electric saw is designed to work with wood, therefore under no circumstances should it be used to cut products from other materials. See, for example, that there are no objects in the wood that can spoil the teeth of the chain, for example, carnations, bolts or iron staples. Even a small metal carnation can damage a lot of teeth, and eventually have to change the whole mountain. Perfect matter for the sake of sawing - dry wood logs, boards or bars, according to the width (diameter) not exceeding the length of the tire. In order to cut a large trunk into fairly girths, use a gasoline saw of an industrial type In order not to accidentally"cut"the saw, use special high-end stands or"goats"and see that the frame from the mountain is not in contact with the ground. The cutting is forced to be done freely, without"snacks", if the teeth do not grasp the tree species or the frame moves with difficulty - it's time to perform the sharpening. Be sure to observe the interval order - allow the electric saw to calm down. By the way, lubricate the structure and look, so that there is no overheating. Observance of several usual rules will increase the length of the building of an electric saw and will allow the realization of an abundance of fascinating plans.