How to make a garden wheelbarrow by yourself...

How to make a garden wheelbarrow by yourself : decorative and practical optionsFor the garden, there are always lots of cases. Sometimes you have to put off something heavy, and it's not always useful for the sake of health. Mostly hard for those who are not accustomed to serious physical stress. In order to receive through the stay for the dacha a pleasure, and not a disease in the spine, we must not steal the heaviness in our hands, but transport them for the cart. The garden wheelbarrow made by own hands from improvised materials, pretty good assistant for the gap of construction, harvesting and other works. Moreover, for the sake of its construction, no special abilities or materials are useful. All that is needed, or already eat for the dacha, or it's easy to bribe.
Variation #1 - a sturdy and usual wooden wheelbarrow
A garden and building wheelbarrow is allowed to bribe in every store. However, there is no need to spend money in vain, if it is permissible to perform it without the help of others? Drawings for the construction of wood wheelbarrows are not useful: the work is simple and does not require significant material costs. If something is not enough, in the course of work, you can always buy it. Suggestion. The construction of a wheelbarrow must be given importance to hard varieties of wood species: elm, birch, oak or maple. Such matter will serve endlessly and is quite reliable in operation. Coniferous rocks are better not to be extracted. We make the assembly frame
From the planed boards we collect the box - the base of the product. We choose the sizes proceeding from the physical preparation and needs of an economy. In our example, the width of the box is 46 cm and its length is 56 cm.
The box and wheel will be strengthened for the mounting frame - the main wheelbarrow support. For the sake of its construction we need two brusks 3-5 cm wide and 120 cm long separate. We will also take these bars out as handles for the wheelbarrow. Because of their ends, they are comfortable to handle in order to carry loads according to the terrain area. It is truly right to choose wood for the sake of a wheelbarrow: softwoods are more resistant to decay, more deformed during use and, in the long run, are not enough The bars are laid for food, connecting the front ends together. We extend the opposite ends of the bars for the width of our own shoulders. For the connected ends from above, we place the bar of the smallest diameter. For the photo, it is shown in a different color. It should be outlined in pencil, leaving parallel bars for the bars of the frame. For no apparent reason, we mark out a room where, after the bars, a wheel is fairly fitted. In accordance with the lines made at the bars we make cuts with a hacksaw or a circular saw for no reason, like shown for a photo.
The wheel is also rather woody
A wheel with a diameter of 28 cm, we will also act from the tree species. We take 6 perfectly cut plates with dimensions of 30x15x2 cm. We glue them into a square for no reason, as shown for the figure, with the help of PVA glue. We hold about a press about a day: before the glue dries completely. For the surface of the square, we mark the circle. Precise fasten the future wheel with wood screws. We drill the wheel, orienting ourselves for the outer part of the markup. A rough rim is treated with a rasp. If you are doing a wheelbarrow to work in the garden, it is better to bribe the finished wheel (iron with a rubber tire). And if you make a decorative wheelbarrow, then nothing better than a tree
Mount the frame and wheel
We return to the mounting frame. Two bars are connected between each other by means of a spacer. It should be established without cause, so that between the front ends of the bars (those that are cut from the inside) the wheel is placed. To be the width of the wheel of 6 cm, the gap between the ends of the bars should exist 9 cm. Based on these judgments, we determine the size of the spacer, we clip its ends and attach it to the bars with screws.
For ironing the wheel, we will use an iron mockery length 150-200 mm, 4 nuts and 4 washers. It is unrestricted across a diameter of 12-14 mm. For the ends of the bars drill holes for the sake of this hairpin. Seem in the center of our wood wheel we drill a hole that is slightly more than the diameter of the hairpin. As if the body in the wheelbarrow of metal is welded to its mounting frame. The main points of work are similar and do not depend on the material used.
The only end of the hairpin is pushed into the hole for one of the bars. We fix for the pin the washer, later the nut, then the wheel, then one more nut and washer. We pass the hairpin through the 2nd log. Fix the wheel from the outside of the bars with washers and nuts. The stud must be aggressively secured to the bars, therefore tighten the fastening with 2 wrenches.
It remains to assemble the finished work
For the upside-down box, place the mounting frame with the wheel for no reason, so that the wheel does not touch the box. Note the location of the frame for the box in pencil. We make two wedges for the entire length of the box with a width of 5 cm and a width of 10 cm. We put them for the pencil strips and attach them to the surface of the box with screws from the bottom of the article. To these wedges, too, we fix the frame with the wheel with screws. It remains to install the spacer, which aggressively holds the posts between them. The wheelbarrow is ready, it is allowed to rip it with linseed oil and extract it in works
We make brackets-brackets so that the wheelbarrow can be comfortably evaluated for loading and unloading. We select their length so that the installation for their box is placed in parallel withEarth. Rigid unity of the pillars provides a bar-spacer attached for no reason, like shown for photos. It remains to cover the finished work with linseed oil, so that the wheelbarrow served you faithfully and truthfully for many years. The wheelbarrow from the tree serves endlessly for satisfaction to the owners, and then the product fails to clutter up, and decorates the part as a creative flower bed >
This cart looks pretty decorative and can decorate every part of it, if it is no longer useful.
Variation #2 - wheelbarrow from metal or barrel
The universal wheelbarrow, which can be removed and harvested, and must be carried out, must be strong. For the transport of cement, sand or soil, it is better to extract metal work. Without the help of others, it is not difficult to perform such a wheelbarrow, but knowledge of working with welding equipment is useful.
A good option is to start a cart, welded from a sheet of metal, 2 mm wide. First, the body is assembled from the sheet, after which the chassis and handles are welded to it. Depends on the intended load for the finished work, for the sake of it wheels can exist through the bike, the moped and even large. Usually, such barrels get to their owners"on occasion"and cost quite inexpensively, and the garden wheelbarrow from this steel barrel is quite light and very comfortable.
Half of the barrel, cut open alike, is fixed for the frame. Near the supporting frame it is necessary to weld arcs or pipes, which will amuse the occupation of the racks. They are necessary, so that the wheelbarrow has the necessary stability to be handling.
Now, if you understand, like doing a wheelbarrow without the help of others, you do not have to buy in stores products from China that are enough to continue.