Motoblock is an irreplaceable assistant to the owner of a personal farmstead, a garden or a summer residence. Small-sized technology came to replace the languid manual labor, which made it possible to improve the property of cultivating the land and save time for each operation. With the arrival of winter, the motoblock is allowed to be removed for the sake of snow removal. It is simpler only to perform a snowplow from a motoblock with your own hands using a special snow-removal nozzle assembled in industrial conditions. All craftsmen prefer not to spend excessive funds for ready-made attachments, but to recruit from the available spare parts and the construction of materials a home snowplower to the motor block, working in accordance with the same principle as the factory products.
Snow-removing attachments for motoblock: future and application Manufacturers of pendant equipment offer three options for snow-removing attachments to the motor block, differing in the method of harvesting the snow mass. Only just deposited sediment is perfectly swept off the surface to be cleaned by means of rigid rotating brushes. This snowplower for the motoblock is indispensable where the paths and platforms have a decorative coating that can not be damaged to be cleaned up by snow. The brush is strengthened by a canopy for the rotating shaft.
Izza single hole motoblock, equipped with a brush, clears the track width of 1 meter in front. It is allowed to excite the angle of capture in three directions: on the left, the future, on the right. Is subject to adjustment and stripping, which simplifies the introduction of hanging equipment. Rigid brush, connected to the motor block, is suitable for cleaning freshly fallen soft snow. This suspension situation is adjusted in accordance with the altitude, it also turns to the left and to the right.
Like to turn the motoblock into a small bulldozer? With wet and caked snow, you can not cope with rigid rotating brushes. It is necessary to remove the pendant snow shovel with knives. Motoblock with a nozzle recalls a small bulldozer, who can loosen a discharge of snow, plunder the snow mass and move it to the dump. The lower limit of the shovel manufacturers deliberately hammered rubber tape, in order to protect not only the cleaned species, but personally the gun through possible damage. Strengthen the hanging snow shovel to the traction device with the help of the front part of the universal hitch. The width of the surface to be cleaned at one time is also a single meter. The blade can be adjusted vertically and in 3 directions. The speed of the motor block equipped with this shovel in the cleaning interval is 2 before 7 km/h. The snow shovel is connected to the motor block in this case, if it is necessary to clear the area of the manor through the languid and caked snow
The ability of the snow thrower of the rotary type With a large volume of snow mass, it is easier to control the snow thrower of the rotor type. To use this suspension snowplower for the sake of the motor block, which has more performance from all the options considered, it is possible to make a snow town for a depth of 250 mm. The main elements of the design of this nozzle is a simple auger, who mixes with a paddle wheel. The rotating auger grasps the snow mass, which moves upward with the help of a paddle wheel. Sediment, passing through a special bell, is thrown out forcefully beyond the boundaries of the cleared track or platform. To see due to the work of the rotary snow-removing nozzle, attached to the motor block, is very interesting. The overhead snowplower for the rotary-type motoblock has a higher productivity, therefore it can freely handle large volumes of fallen snow.
Proud! In the design of universal motor blocks, there is no foreseen the presence of systems protecting the rotor through ingress of pebbles and ice. This function is indispensable for winter special equipment. It is necessary to keep in mind a relative of this and, while driving a motor-block, to be attentive. In an unpleasant situation it is necessary to repair the snow-removal nozzle. Tips on how to use the motoblock in the winter season
Taking into account that the motoblock is all the same basically designed to work in the warm season, then to be exploited in winter the atmosphere is the desire to have in the warmth. This will allow not to spend time for warming up the engine, and to start at once to clear snow.
It would be nice to change the applied quality of oil for the sake of the reducer. Due to the effect of low temperatures, the oils are thickened. Therefore, it is recommended to run over for more watery brands or at any time to receive synthetic oils specially designed for extreme criteria.
The action of a self-made snowplower For the sake of snow removal, it is permissible to use not the motoblock itself, but only its engine. Roof iron agree for the action of the snow auger auger body. Plywood 10 mm thick is suitable for the creation of sidewalls. The rim is welded from the iron corner. A half-inch pipe is fitted around the handle, and a three-quarter inch tube is made from the auger elevation. The through cut, made in the center of the pipe, serves to fix the iron plate (blade), having dimensions of 120 for 270 mm. The blade is designed to rotate the shaft to rotate the sludge. To move the snow mass to the blade in this homemade snowplow construction is forced by a two-auger screw, for the production of which a sidewall of the tire is taken, or a conveyor belt with a thickness of 10 mm. Quite a half meter of such tape, in order to cut four rings with an electric jigsaw. The diameter of each of them is forced to exist is equal to 28 cm. For the production of self-made snow-plows, roofing iron, plywood, conveyor belt, pipes of various diameters, iron corners, closed bearings are useful . For the fastening of the platform of the quick-release motor, borrowed from the motor block, to the pipe Iron corners are welded perpendicular to the plate. For the sake of free entry of the shaft into the self-centering closed bearings 205, it is necessary to execute a pair of cuts for its ends and to tap them. Then this operation decreases the diameter of the shaft. For the sake of a key, an indentation is made about the sprocket on one side of the shaft.
Proud! Bearings must exist necessarily closed, because it is impossible to favor snow falling into them. The auger is driven by a chain or belt, if a pulley is installed for the engine through the motor block. All the necessary parts (pulleys, belts, bearings) are allowed to be bribed in auto shops. It's better to evaluate the design not for wheels that will linger in the snow, but for skis. From the wooden bars, the skis are ground, for which the plastic lining is reinforced for the best gliding. As linings, it is permissible to remove the boxes used to be wiring harnesses. The snow-scooter for skiing is easier to slide according to the snow cover, hence the person managing it has to add less physical effort The swivel trough, which is needed to tilt the snow in a suitable direction, is made from a plastic sewer pipe of a huge diameter (more than 160 mm). Fasten it for the same tube of the smallest diameter, attached to the auger body. To the pivoting trench, reinforce the lining of the sewer pipe, which is enough to reverse the ejection of snow. The diameter of the gutters have to win the width of the screw blade so as not to keep the promotion of the snow mass, leaning back with her through.
Proudly! Turning trough allows you to adjust not only the trend of the snow throw, but also the range. The length of the gutter affects the gap, The visibility of the self-made snow-scooter, equipped with the engine through the motor-block, in the assembled state before checking its efficiency in the snowy courtyard of the personal house. To give the homemade design a representative appearance, it is necessary to paint its details in all parts shining paint. Then the end of the work is tested, and then it is used only during the winter period. Some masters go further, making a self-propelled variation of the snow-picker.
Механизировать легкий дело стремятся безвыездно человек, живущие для земле. Прочитав, вроде исполнять снегоуборщик из мотора мотоблока и других запчастей, некие не станут «изобретать велосипед», а решат подкупать заводскую образец снегоуборщика. Ради покупки экономного варианта будет нужно близ 20-30 тыс. рублей. Доход насадки промышленного производства к мотоблоку обойдется дешевле в полтора-два раза. Ради сборки самодельной конструкции придется потратиться только на покупку неких запчастей, также выделить ради выполнения работ пару дней.In any case, the issue of cleaning snow from the local area is quite resolved.
Комментариев нет:
Отправить комментарий